Is there a logical reason the Geekworm X1003 would not work on the...

[/RaspberryPi]

Is there a logical reason the Geekworm X1003 would not work on the Ubuntu image that the Raspberry Pi Imager can create? I have a whole server set up and running perfectly on a Raspberry Pi 5B 8GB with Nextcloud, PlexMediaServer, Airsonic, samba, webmin, etc. All works great -- even mdadm. But even after following ALL directions in Geekworm's wiki first, updating eeprom, updating /boot/firmware/config.txt, etc,. sudo lsblck, and sudo dmesg don't seem to see this device or the attached "KingSpec 512GB 2230 SSD NVMe Gen3x4, M.2 PCIe 3.0 SSD with 3D NAND Flash".

I can't see any lights on the geekworm X1003, nor on the M.2.

Is there anything that would be missing in the Ubuntu image that would prevent this from working?

~$ sudo lsblk

NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS

loop0 7:0 0 4K 1 loop /snap/bare/5

loop1 7:1 0 177M 1 loop /snap/airsonic/167

[redacted]

loop25 7:25 0 35.5M 1 loop /snap/snapd/20298

mmcblk0 179:0 0 238.8G 0 disk

├─mmcblk0p1 179:1 0 512M 0 part /boot/firmware

└─mmcblk0p2 179:2 0 238.2G 0 part /var/snap/firefox/common/host-hunspell

/

:~$

:~$ sudo dmesg | grep pcie

[ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=1 pci=pcie_bus_safe snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 smsc95xx.macaddr=D8:3A:DD:DB:55:22 vc_mem.mem_base=0x3fc00000 vc_mem.mem_size=0x40000000 zswap.enabled=1 zswap.zpool=z3fold zswap.compressor=zstd multipath=off dwc_otg.lpm_enable=0 console=tty1 root=LABEL=writable rootfstype=ext4 rootwait fixrtc quiet splash

[ 0.558187] brcm-pcie 1000110000.pcie: host bridge /axi/pcie@110000 ranges:

[ 0.558198] brcm-pcie 1000110000.pcie: No bus range found for /axi/pcie@110000, using [bus 00-ff]

[ 0.558220] brcm-pcie 1000110000.pcie: MEM 0x1b00000000..0x1bfffffffb -> 0x0000000000

[ 0.558230] brcm-pcie 1000110000.pcie: MEM 0x1800000000..0x1affffffff -> 0x0400000000

[ 0.558241] brcm-pcie 1000110000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000

[ 0.559371] brcm-pcie 1000110000.pcie: Forcing gen 2

[ 0.559585] brcm-pcie 1000110000.pcie: PCI host bridge to bus 0000:00

[ 0.992568] brcm-pcie 1000110000.pcie: link down

[ 0.992918] pcieport 0000:00:00.0: PME: Signaling with IRQ 43

[ 0.993033] pcieport 0000:00:00.0: AER: enabled with IRQ 43

[ 0.993642] brcm-pcie 1000120000.pcie: host bridge /axi/pcie@120000 ranges:

[ 0.993649] brcm-pcie 1000120000.pcie: No bus range found for /axi/pcie@120000, using [bus 00-ff]

[ 0.993673] brcm-pcie 1000120000.pcie: MEM 0x1f00000000..0x1ffffffffb -> 0x0000000000

[ 0.993685] brcm-pcie 1000120000.pcie: MEM 0x1c00000000..0x1effffffff -> 0x0400000000

[ 0.993708] brcm-pcie 1000120000.pcie: IB MEM 0x1f00000000..0x1f003fffff -> 0x0000000000

[ 0.993721] brcm-pcie 1000120000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000

[ 0.994854] brcm-pcie 1000120000.pcie: Forcing gen 2

[ 0.994938] brcm-pcie 1000120000.pcie: PCI host bridge to bus 0000:00

[ 1.100577] brcm-pcie 1000120000.pcie: link up, 5.0 GT/s PCIe x4 (!SSC)

[ 1.112778] pcieport 0000:00:00.0: enabling device (0000 -> 0002)

[ 1.112839] pcieport 0000:00:00.0: PME: Signaling with IRQ 44

[ 1.112973] pcieport 0000:00:00.0: AER: enabled with IRQ 44

:~$

$ sudo rpi-eeprom-update

BOOTLOADER: up to date

CURRENT: Wed Jan 24 12:16:01 UTC 2024 (1706098561)

LATEST: Mon Sep 25 10:44:03 UTC 2023 (1695638643)

RELEASE: default (/lib/firmware/raspberrypi/bootloader-2712/default)

Use raspi-config to change the release.

:~$

​

​

:~$ sudo rpi-eeprom-config

[all]

BOOT_UART=1

POWER_OFF_ON_HALT=0

PCIE_PROBE=1

BOOT_ORDER=0xf41

:~$

​

:~$ cat /boot/firmware/config.txt | tail

​

# Config settings specific to arm64

arm_64bit=1

dtoverlay=dwc2

​

# Enable the PCIe External connector.

dtparam=pciex1

# This line is an alias for above (you can use either/or to enable the port).

#dtparam=nvme

#dtparam=pciex1_gen=2

:~$

:~$ sudo apt update

Hit:1 http://ports.ubuntu.com/ubuntu-ports mantic InRelease

Hit:2 http://ports.ubuntu.com/ubuntu-ports mantic-updates InRelease

Ign:3 https://download.webmin.com/download/newkey/repository stable InRelease

Hit:4 http://ports.ubuntu.com/ubuntu-ports mantic-security InRelease

Hit:5 https://download.webmin.com/download/newkey/repository stable Release

Reading package lists... Done

Building dependency tree... Done

Reading state information... Done

All packages are up to date.

:~$

​
submitted by /u/etyrnal_
[link] [comments]

Source: https://www.reddit.com/r/raspberry_pi/c ... orm_x1003/